To download any of the files below, right-click on the desired link and choose "Save Target As...". Specify a location on your hard drive.
For ZIP files, you can then use PKZIP or WinZIP to unpack the contents.
Centroid v3.16 (Windows) Mill Operator's Manual (15.6MB PDF)
Centroid v3.16 (Windows) Lathe Operator's Manual (11.5MB PDF)
Centroid v2.70 (Linux) Mill Operator's Manual (14.2MB PDF)
Centroid v2.70 (Linux) Lathe Operator's Manual (10.5MB PDF)
Centroid v2.32 (Linux) Mill Operator's Manual (5.1MB PDF)
The pagination in the 2.32 Mill PDF file is wrong. For best results when printing double-sided, print it in pieces as follows:
Centroid v2.32 (Linux) Lathe Operator's Manual (4.3MB PDF)
Centroid v8.22 (DOS) Mill Operator's Manual (4.3MB PDF)
Centroid v8.22 (DOS) Lathe Operator's Manual (3.9MB PDF)
Centroid v7.17 (DOS) Mill Operator's Manual (8.9MB PDF)
Centroid v7.06 (DOS) Mill Operator's Manual in Spanish (1.6MB ZIP archive)
Install an entry on the F5/CAM menu which will generate, and optionally export, a printable text copy of your tool library. This can serve as a handy reference when writing new part programs.
Tool List for Linux CNC10
Tool List for DOS CNC7
To install: unpack the ZIP file to a floppy diskette or USB drive; insert it in the control computer and press F7/Utility, then F2/Update.
To make a tool list: insert a floppy disk or plug in your USB drive;
press F5/CAM; and press the key for ToolList. Take the disk or USB
drive to your desktop computer and open the file
(from Linux) or
CNC7TOOL.TXT (from DOS).
Centroid's offline Intercon conversational programming software comes with a Sentinel parallel port key or USB key. This key requires a driver to be installed in order to work with Microsoft Windows.
Click here to go to the SafeNet web page containing the current Sentinel driver for Windows, then click on "Sentinel SuperPro".
Centroid's consoles no longer include floppy disk drives. Instead Centroid provides USB ports. For a year or so after the change over to USB in 2005, Centroid included a Swissbit "Twist" USB flash drive with each control console. This device works automatically on the Centroid console with Linux, and on any PC running Windows XP. If you wish to use the Swissbit Twist USB drive on a computer running Windows 98, you need to download and install a driver for it.
Click here to go to the Swissbit support page containing the Windows 98 driver.
A utility to correct the date on computers with non-Y2K-compliant BIOS. These include most M15 and M400 controls built before December 1998 (M15 serial numbers below K4402 and M400 serial numbers below K6398).
Unpack the ZIP file to a floppy diskette; insert it in the control computer and press F7/Utility, then F2/Update.
Driver needed to run Mastercam 3.21 under Windows 9x
Unpack the ZIP file to a floppy diskette; insert it in the control computer and press F7/Utility, then F2/Update (or use Windows to run A:INSTALL.BAT).
A utility to calculate optimal spindle speed settings on the Control Configuration screen. These are the settings that match the RPM displayed on the screen to the RPM the inverter is actually commanding.
First note the previous values on the Control Configuration screen, and make two measurements of actual RPM (with a tachometer) vs. the RPM displayed on the screen. For best results make one set of measurements at a low speed (around 10%) and the second set at a high speed (around 90%).
Then run SPINCAL from the command line. Enter the information you collected. SPINCAL will tell you the best new numbers to enter on the Control Configuration screen.
Run SPINCAL with a command line argument of "/?" for instructions.
Copyright © 2016 Marc Leonard
Last updated 16-Nov-2016 MBL